Features
Current servos have the appearance of high speed and high power from the response of 2.4GHz and the power from Li-po batteries respectively. This creates a huge demand upon the servo. The RSx is the racing servo with the durability and operability to employ this high-spec demand.
1:Case
The middle case is machined from one piece of aluminum that incorporates the gear pins and motor being held properly in place. The top case rigidity has been improved with the addition of two screws in the middle to prevent flex and keep the gears properly aligned. The upper Hard Case (H.C) is also machined from aluminum. H.C is the distinction of durability for categories that demand high stress.
2:Motor
A servo motor is a very important part of a servo. The specification of a servo is up to the motor being used. We have developed a new motor suitable for the new R/C standard with numerous performance and stress tests.
3:Gear
The gears are made with a special Japanese aluminum. This gear is 45% lighter than brass and has the same hardness as steel. The ‘Light Weight’ design provides a clean response for driving and reduces the burden on the servo motor. The thorough quality control of the manufactured gears ensures the least amount of backlash possible for smooth action.
| Speed: | 0.07s@60°(7.4V) 0.09s@60°(6.0V) |
| Torque: | 9.0kg-cm(7.4V) 7.0kg-cm(6.0V) |
| Size: | 41 x 25.5 x 21 mm |
| Weight: | 51.0 g |
RSx one10 Response (Low Profile Digital Servo, Speed Type)
The RSx one10 Response is designed for electric or nitro 1/10th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC or ICS setting card for the RSx for further fine tuning.
| Speed: | 0.09s@60°(7.4V) 0.1s@60°(6.0V) |
| Torque: | 12.0kg-cm(7.4V) 10.0kg-cm(6.0V) |
| Size: | 41 x 25.5 x 21 mm |
| Weight: | 51.5 g |
RSx one10 (Low Profile, Digital, Torque Type)
The RSx one10 is designed for electric or nitro 1/10th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC or ICS setting card for the RSx for further fine tuning.
| Speed: | 0.13s@60°(6.0V) |
| Torque: | 7.5kg-cm(6.0V) |
| Size: | 33 x 26 x 15 mm |
| Weight: | 26.0 g |
RSx12 (Mini Servo, Digital)
The RSx12 is designed for electric 1/12th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC or ICS setting card for the RSx for further fine tuning.
| Speed: | 0.08s@60°(7.4V) 0.09s@60°(6.0V) |
| Torque: | 8.2kg-cm(7.4V) 7.0kg-cm(6.0V) |
| Size: | 40.5 x 26.5 x 21 mm |
| Weight: | 42.1 g |
RSx one10 Type-S (Low Profile, Digital, Steering Type)
The RSx one10 Type-S is designed as a budget servo with high performance specs for electric or nitro 1/10th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC for further fine tuning.
| AGS Function: | Adjust Gain Sensor |
| PCA Function: | Priority Control Adjuster |
| EPA: | End Point Adjustement |
| Size: | 20.0 x 24.0 x 14.0 mm |
| Weight: | 8.3 g |
| Operating Voltage: | 4.8 to 7.4V |
| Input Channel: | 2ch (Steering signal: 1ch) |
The KG-X is Intelligent steering assist Gyro unit which is optimized for use with RWD drift car. Next generation Gyro system, covering all required functions for Drift cars, such as AGC function, End point adjust (each L/R ) function, PCA function, etc. *KG-X is a collaboration product with OverDose company.
AGS restrains vibration of servo!
With a conventional gyro system, servo vibrations occur when increasing gain setting. The AGC function equipped with KG-X enables to stop the vibration and operate servo normally.
Priority Control Adjuster (PCA)
The mixing ratios of the gyro signal and steering signal can be changed. Steering control performance can be obtained without feeling the use of the gyro. * If you want to use the gain setting via the transmitter, please use a 4ch transmitter.
