

Features
Based on the successful high-quality of the RSx series the BSx series goes through the transformation in the second series as the BSx2. Now offering the BSx2 in the Response (speed type) and Power (torque type) versions with the option of the plastic upper case or the Hard Case (H.C. aluminum). The BSx2 series was developed using a brushless motor to utilize the result of technology to maximize efficiency and long life.
1:Case
Quality that is made in Japan. The middle case is machined from one piece of aluminum that incorporates the gear pins and motor being held properly in place. The top case rigidity has been improved with the addition of two screws in the middle to prevent flex and keep the gears properly aligned. The upper Hard Case (H.C) is also machined from aluminum. H.C is the distinction of durability for categories that demand high stress.
2:Motor
A servo motor is a very important part of a servo. The specification of a servo is up to the motor being used. We have used a brushless motor that is made in Japan for quality and performance.
3:Gear
The gears are made with a special Japanese aluminum. This gear is 45% lighter than brass and has the same hardness as steel. The ‘Light Weight’ design provides a clean response for driving and reduces the burden on the servo motor. Power versions now include a stainless steel gear along with the aluminum gears to further increase the strength. The thorough quality control of the manufactured gears ensures the least amount of backlash possible for smooth action.

Speed: | 0.09s@60°(7.4V) 0.1s@60°(6.0V) |
Torque: | 10.8kg-cm(7.4V) 8.0kg-cm(6.0V) |
Size: | 40.5 x 26 x 21 mm |
Weight: | 51.0 g |
BSx2 one10 Grasper (Low Profile, Digital, Steering Type)
The BSx2 one10 Grasper is designed as a steeringfor electric or nitro 1/10th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC for further fine tuning.






Speed: | 0.08s@60°(7.4V) 0.09s@60°(6.0V) |
Torque: | 13.3kg-cm(7.4V) 10.5kg-cm(6.0V) |
Size: | 40.5 x 26 x 21 mm |
Weight: | 48.0 g |
BSx2 one10 Response (Low Profile, Digital, Speed Type)
The BSx2 one10 Response is designed for electric or nitro 1/10th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC or ICS setting card for the RSx for further fine tuning.





Speed: | 0.10s@60°(7.4V) 0.12s@60°(6.0V) |
Torque: | 17.8kg-cm(7.4V) 15.2kg-cm(6.0V) |
Size: | 40.5 x 26 x 21 mm |
Weight: | 48.0 g |
BSx2 one10 Power (Low Profile, Digital, Torque Type)
The BSx2 one10 Power is designed for electric or nitro 1/10th scale vehicles. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC or ICS setting card for the RSx for further fine tuning.





Speed: | 0.08s @60°(7.4V) 0.09s @60°(6.0V) |
Torque: | 18.1 kg-cm(7.4V) 15.4 kg-cm(6.0V) |
Size: | 41 x 37.5 x 20 mm |
Weight: | 70.5 g |
The BSx2 Response H.C. (Hard Case) is designed for ultimate rigidity while still providing high speed. This servo comes ready to operate at 6V or 7.4V.Programming of this servo will also be available via PC for further fine tuning. Recommended for use on steering for 1/8th off-road buggy, 1/8th on-road and 1/10th GP on-road.





AGS Function: | Adjust Gain Sensor |
PCA Function: | Priority Control Adjuster |
EPA: | End Point Adjustement |
Size: | 20.0 x 24.0 x 14.0 mm |
Weight: | 8.3 g |
Operating Voltage: | 4.8 to 7.4V |
Input Channel: | 2ch (Steering signal: 1ch) |
The KG-X is Intelligent steering assist Gyro unit which is optimized for use with RWD drift car. Next generation Gyro system, covering all required functions for Drift cars, such as AGC function, End point adjust (each L/R ) function, PCA function, etc. *KG-X is a collaboration product with OverDose company.
AGS restrains vibration of servo!
With a conventional gyro system, servo vibrations occur when increasing gain setting. The AGC function equipped with KG-X enables to stop the vibration and operate servo normally.
Priority Control Adjuster (PCA)
The mixing ratios of the gyro signal and steering signal can be changed. Steering control performance can be obtained without feeling the use of the gyro. * If you want to use the gain setting via the transmitter, please use a 4ch transmitter.



Speed: | 0.12s @ 60°(7.4V) 0.15s @ 60°(6.0V) |
Torque: | 26.0 kg-cm(7.4V) 21.0 kg-cm(6.0V) |
Size: | 41 x 37.5 x 20 mm |
Weight: | 68.5 g |
The BSxs Response H.C. (Hard Case) is designed for ultimate rigidity while providing high torque. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC for further fine tuning. Recommended for use on steering/throttle for 1/8th off-road buggy, and steering/throttle for 1/8th on-road.





Speed: | 0.08s @60°(7.4V) 0.09s @60°(6.0V) |
Torque: | 18.1 kg-cm(7.4V) 15.4 kg-cm(6.0V) |
Size: | 41 x 38 x 20 mm |
Weight: | 62.4 g |
BSx2 Response (Brushless, Digital Servo, Speed Type)
The BSx2 Response is designed to provide high speed. This servo comes ready to operate at 6V or 7.4V.
Programming of this servo will also be available via PC for further fine tuning.
Recommended for use on steering for 1/8th off-road buggy, 1/8th on-road and all 1/10th scale vehicles.





Speed: | 0.12s @ 60°(7.4V) 0.15s @ 60°(6.0V) |
Torque: | 26.0 kg-cm(7.4V) 21.0 kg-cm(6.0V) |
Size: | 41 x 38 x 20 mm |
Weight: | 63.5 g |
BSx2 Power (Brushless, Digital Servo, Torque Type)
The BSx2 Power is designed to provide high torque. This servo comes ready to operate at 6V or 7.4V.
Programming of this servo will also be available via PC for further fine tuning.
Recommended for use on steering/throttle for 1/8th off-road buggy and steering/throttle for 1/8th on-road.



