

Features
The original RSx Response/Power servos took a servo to a higher level upon it’s release. The RSx2 is the further development of the RSx series and we have raised the bar again. Gear and the aluminum case are within 0.01mm tolerance. Re-working of the servo amplifier has created a more linear feel with today’s faster transmitter systems.
1:Case
The middle case is machined from one piece of aluminum that incorporates the gear pins and motor being held properly in place. The top case rigidity has been improved with the addition of two screws in the middle to prevent flex and keep the gears properly aligned. The upper Hard Case (H.C) is also machined from aluminum. H.C is the distinction of durability for categories that demand high stress.
2:Motor
A servo motor is a very important part of a servo. The specification of a servo is up to the motor being used. We have developed a new motor suitable for the new R/C standard with numerous performance and stress tests.
3:Gear
The gears are made with a special Japanese aluminum. This gear is 45% lighter than brass and has the same hardness as steel. The ‘Light Weight’ design provides a clean response for driving and reduces the burden on the servo motor. Power versions now include a stainless steel gear along with the aluminum gears to further increase the strength. The thorough quality control of the manufactured gears ensures the least amount of backlash possible for smooth action.

Speed: | 0.06s @60°(7.4V) 0.07s @60°(6.0V) |
Torque: | 17.6 kg-cm(7.4V) 14.5 kg-cm(6.0V) |
Size: | 41 x 37.5 x 20 mm |
Weight: | 70.5 g |
The RSx2 Response H.C. (Hard Case) is designed for ultimate rigidity while still providing high speed. This servo comes ready to operate at 6V or 7.4V.Programming of this servo will also be available via PC for further fine tuning. Recommended for use on steering for 1/8th off-road buggy, 1/8th on-road and 1/10th GP on-road.





Speed: | 0.11s @ 60°(7.4V) 0.13s @ 60°(6.0V) |
Torque: | 31.6 kg-cm(7.4V) 26.3 kg-cm(6.0V) |
Size: | 41 x 37.5 x 20 mm |
Weight: | 70.5 g |
The RSx Response H.C. (Hard Case) is designed for ultimate rigidity while providing high torque. This servo comes ready to operate at 6V or 7.4V. Programming of this servo will also be available via PC for further fine tuning. Recommended for use on steering for 1/8th off-road truggy, throttle for 1/8th off-road buggy/truggy and throttle for 1/8th on-road.





AGS Function: | Adjust Gain Sensor |
PCA Function: | Priority Control Adjuster |
EPA: | End Point Adjustement |
Size: | 20.0 x 24.0 x 14.0 mm |
Weight: | 8.3 g |
Operating Voltage: | 4.8 to 7.4V |
Input Channel: | 2ch (Steering signal: 1ch) |
The KG-X is Intelligent steering assist Gyro unit which is optimized for use with RWD drift car. Next generation Gyro system, covering all required functions for Drift cars, such as AGC function, End point adjust (each L/R ) function, PCA function, etc. *KG-X is a collaboration product with OverDose company.
AGS restrains vibration of servo!
With a conventional gyro system, servo vibrations occur when increasing gain setting. The AGC function equipped with KG-X enables to stop the vibration and operate servo normally.
Priority Control Adjuster (PCA)
The mixing ratios of the gyro signal and steering signal can be changed. Steering control performance can be obtained without feeling the use of the gyro. * If you want to use the gain setting via the transmitter, please use a 4ch transmitter.



Speed: | 0.06s @60°(7.4V) 0.07s @60°(6.0V) |
Torque: | 17.6 kg-cm(7.4V) 14.5 kg-cm(6.0V) |
Size: | 41 x 38 x 20 mm |
Weight: | 65.6 g |
RSx Response (Digital Servo, Speed Type)
The RSx Response is designed to provide high speed. This servo comes ready to operate at 6V or 7.4V.
Programming of this servo will also be available via PC for further fine tuning.
Recommended for use on steering for 1/8th off-road buggy, 1/8th on-road and all 1/10th scale vehicles.





Speed: | 0.11s @ 60°(7.4V) 0.13s @ 60°(6.0V) |
Torque: | 31.6 kg-cm(7.4V) 26.3 kg-cm(6.0V) |
Size: | 41 x 38 x 20 mm |
Weight: | 65.6 g |
RSx Power (Digital Servo, Torque Type)
The RSx Response is designed to provide high torque. This servo comes ready to operate at 6V or 7.4V.
Programming of this servo will also be available via PC for further fine tuning.
Recommended for use on steering for 1/8th off-road truggy, throttle for 1/8th off-road buggy/truggy and throttle for 1/8th on-road.



